---
id: benchmarks
type: guide
title: Benchmarks and throttle tests
summary: Therbie's quick benchmark measures CPU, GPU, on-device AI, memory and storage speed in about a minute. The 5- or 15-minute throttle test shows how much of its peak speed the device keeps once it's hot. A Charger Test times how fast the battery fills.
section: device
url: "https://irrhuh.app/therbie/guide/benchmarks.html"
related: [throttle-test-length, thermal-states, device-link, mac-app, glossary]
platform: [iphone, ipad]
applies_to: 1.0
updated: 2026-11-16
---

# Benchmarks and throttle tests

Therbie on iPhone and iPad has two speed tests:

- **Quick benchmark:** how fast the device is right now, in real units such as GFLOPS (billions of calculations per second).
- **Throttle test:** how much of that speed the device keeps once it gets hot.

The Benchmark screen also has a **Charger Test**, which times how fast the battery fills.

To open the Benchmark screen, go to the **Device** tab and tap **Run tests** on the **Benchmark** card.

![The Benchmark screen, shown in the Simulator on a Mac. The figures are the Mac's, and the orange notes flag a debug build and leftover heat](https://irrhuh.app/therbie/img/ios-benchmark.jpg)

## Run the quick benchmark

1. Let the device cool down until the **Thermal** card says **Normal**.
2. On the Benchmark screen, tap **Run Benchmark · about 1 min**.
3. Keep Therbie on screen until it finishes. The screen stays on meanwhile. If you leave Therbie, the benchmark stops and its results aren't saved.

It measures eight things:

| Group | Test | Unit |
|---|---|---|
| CPU, one core and all cores | Matrix maths, hashing, compression | GFLOPS, MB/s |
| GPU | 32-bit maths | GFLOPS |
| Neural Engine and AI | Image classification | images/s |
| | Language model, reading a long prompt; language model, writing an answer | tokens/s |
| Memory and storage | Memory copy, storage write, storage read | GB/s, MB/s |

The two language-model tests use Apple's on-device model, so they need Apple Intelligence turned on. Elsewhere they show **Not available on this device**, or ask you to turn on Apple Intelligence.

Results are saved. **Saved Runs** lists every benchmark and throttle test.

## Run a throttle test

The throttle test runs the CPU or the GPU flat out and takes a reading every 10 seconds: speed, thermal state, battery level and whether it's charging. The result is **Kept % of peak**: the average of the last 30 seconds divided by the best 10-second reading. 100% means the device never slowed down.

![A throttle test: speed over time, with the thermal state shaded behind. Shown in the Simulator, so the figures are the Mac's](https://irrhuh.app/therbie/img/ios-throttle.jpg)

1. On the **Throttle Test** card, choose **CPU** or **GPU**, and **5 min** or **15 min**.
2. Add a label, such as *With case* or *On a stand*, so you can tell runs apart later.
3. Tap **Start 5-minute test** (or **Start 15-minute test**) and keep Therbie on screen. The screen stays on during the test.

The test stops early in three cases:

- **You leave Therbie.** iOS doesn't allow the test in the background.
- **The device reaches Critical.** Therbie stops the test itself.
- **The device is already at Critical.** The test doesn't start.

**Which length?** Use 5 minutes for the CPU and 15 for the GPU. In the developer's tests on an iPhone 17 Pro, iPad Air and iPad mini, CPU speed settled within about 4 minutes. The GPU kept dipping and recovering for 10 to 15 minutes. [How long should a throttle test be?](https://irrhuh.app/therbie/kb/throttle-test-length.html) has the numbers.

> **Important** A throttle test warms the device and uses battery.

## Compare runs fairly

Results depend on the room as much as the device.

- **Start each run at Normal.** If the device was Warm or under test in the last 10 minutes, a **Leftover heat** notice says how long to wait. iOS can report Normal before the inside has fully cooled.
- **Keep the setup the same:** charge state, screen brightness and position.
- **Label every run,** then compare two in **Saved Runs › Compare Two Runs**. You can show both as GFLOPS or as **% of Peak**.
- **Low Power Mode lowers results.** Therbie warns you when it's on.
- **Debug builds** installed from Xcode show lower CPU results and a **Debug build** note. The % kept isn't affected.

## Charger Test

The **Charger Test** card times how fast the battery fills on a charger, cable or pad, in percentage points per hour.

1. Type what you're testing, or tap a suggestion such as **Cable**, **MagSafe** or **Wireless pad**.
2. Plug in, then tap **Start**. Until you plug in, the button reads **Plug in to start**.
3. Keep Therbie on screen. The test needs at least two changes of battery level, which takes 10 to 30 minutes.

The card shows **Time on charger**, **Battery**, **Charging speed** and **Level changes**. Finished tests appear under **Saved tests**.

- **Best range:** start between 20% and 75%. Above 80%, iOS slows charging on purpose, and Therbie warns that the test will read slow.
- **Speed bands, from the card's ⓘ:** Fast is 90 %/h or more; standard is 50 to 90; slow is 25 to 50; very slow is under 25.
- **Privacy:** tests stay on the device.

## On the Mac

Therbie for Mac collects benchmark and throttle results from your paired devices and compares them on one chart. It can also start tests on them. See [Therbie for Mac](https://irrhuh.app/therbie/guide/mac-app.html#runs-compare) and [Testing devices from your Mac](https://irrhuh.app/therbie/guide/device-link.html).
