Motion instruments
The Vibration sensor in Therbie turns your iPhone or iPad's motion sensors into a set of instruments: a seismograph, a vibration meter, a frequency spectrum, a spirit level, a compass, a magnetic field meter and a rotation meter. It also logs how much the device shook, so you can look back at it in History.
It needs no permission. It's off until you turn it on.
Turn it on
- Go to the Measure tab and tap the Vibration tile.
- The first time, a sheet explains the sensor and shows its settings. Tap Turn On.
After that, a tap on the tile turns Vibration on, and the tile's power button turns it off. When it's on, tap the tile to open the instruments full screen.
Measure › Start › Vibration turns the sensor on and starts recording a session straight away.
When it runs:
- While Therbie is on screen.
- During a recording drive or ride, even with the screen locked. This is controlled by Record vibration with drives and Record vibration with rides under Location in ⋯ › Sensors. Both are on by default. See Location and trips.
The instruments
| Panel | What it shows |
|---|---|
| Seismograph | Acceleration along the device's X, Y and Z axes, newest on the right. Choose 2, 5 or 10 seconds at the bottom. The scale (±m/s²) adjusts to the largest movement on screen |
| Intensity | How strongly the device is shaking right now: the RMS (root mean square) of the acceleration over the last half second, on a scale from 0.01 to 10 m/s². A white line holds the highest level of the last 5 seconds |
| Spectrum | Which frequencies the shaking is made of, from 0 Hz up to half the reading rate. A motor, a washing machine or an engine shows as a clear peak |
| Level | A bubble level. Lay the device flat: the bubble turns green within 1° of level |
| Compass | Heading from magnetic north. Keep the device away from magnets and metal for a steady reading |
| Magnetic field | Field strength in µT (microtesla) on a 0–200 µT bar, with Earth's usual 25–65 µT shaded, and an arrow for its direction. It jumps near a magnet, a speaker, or iron and steel, so it works as a magnet and steel finder. It can't find aluminium, copper, gold or silver. Shows Calibrating… until iOS has calibrated the magnetometer: move the device in a figure of eight |
| Rotation | How fast the device is turning, in degrees per second and rpm, with a bar for each axis. The dial goes up to 720°/s |
Intensity bands, loosely based on the ISO 2631 comfort scale:
| Band | RMS acceleration |
|---|---|
| Still | Under 0.03 m/s² (the sensors' own noise) |
| Faint | 0.03 to 0.05 m/s² (a desk someone is typing on) |
| Light | 0.05 to 0.315 m/s² |
| Moderate | 0.315 to 1 m/s² |
| Strong | 1 to 2.5 m/s² |
| Severe | Above 2.5 m/s² |
Purpose
Purpose chooses what the first instrument measures. Change it with the menu at the top left of the instruments, or under Vibration in ⋯ › Sensors.
| Purpose | What it shows | Use it for |
|---|---|---|
| General | Overall shaking (RMS of all three axes) | Anything |
| Ride comfort | Vibration weighted the way ISO 2631-1 weights it for a seated person, with the standard's comfort scale: from "Not uncomfortable" under 0.315 m/s² to "Extremely uncomfortable" at 2.5 m/s² and above | Comparing cars, seats or roads. Mount the device firmly to the seat rail or floor, the same way in each car |
| Suspension | Up-and-down motion split into body movement (0.5–3 Hz) and wheel hop (8–20 Hz), with the body's bounce frequency | Tuning dampers and springs. Fix the device firmly to the body or corner being tuned |
| Impacts | Separate hits over a threshold, their count and the peak | Bumps, potholes, drops, bats and rackets. Set the threshold in A hit is over: 0.5, 1, 2, 4 or 8 g (default 2 g) |
Sessions
- Tap Record Session at the bottom of the instruments.
- Name it, for example "Car A, highway", and tap Record. Without a name, the session is called by its purpose and the date.
- When you're done, tap the same button, which now reads Stop "Car A, highway" with the seconds recorded.
Each session keeps one row a second. Sessions (top left) lists them side by side with their averages. From there you can use Share Comparison (CSV), Share Session (CSV) and Delete Session. Sessions also appear on the Sessions tab.
For a fair comparison, use the same mount, road and speed each time.
Settings
Under Vibration in ⋯ › Sensors:
- Purpose: described above.
- A hit is over: the Impacts threshold.
- Readings: how many times a second the motion sensors are read, 50 or 100 (default 100). A sensor can only show vibrations up to half as fast as it's read, so 100 a second shows shaking up to 50 Hz (medium battery use) and 50 a second up to 25 Hz (less battery). Engine boom and road roar above 50 Hz are better measured with the Sound Level sensor.
What's logged and where it goes
- History: while Vibration is on, Therbie logs the average and peak intensity every second. History shows a Vibration chart (average, shaded up to the peak) for 1H, 24H and 14D. Insights can mention the strongest shaking of the day and how much of the logged time the device was moving.
- Sessions: kept on the device until you delete them.
- Paired Mac: the vibration log goes to a paired Mac with the rest of History, and sessions are sent too, as summaries and CSV files. See Pair your Mac and devices.
Nothing else leaves the device, except CSV files you share yourself.
Good to know
- The phone's own vibration motor, speaker and handling show up too. To measure something else, rest the device on it without holding it.
- Phone motion sensors are made for movement, not lab measurement. Treat the numbers as a comparison between moments and places, not as calibrated values.