Troubleshooting
Fixes for common problems with Therbie on iPhone, iPad and Mac. If yours isn't here, see Help and contact.
The Mac doesn't see my iPhone or iPad
- On the device, go to the Mac tab and check that Allow my Mac to run tests is on, on the Mac Testing card.
- Keep Therbie on screen on the device. The connection closes shortly after Therbie leaves the screen, even with the floating monitor open. The Mac then shows the device greyed out or as Not on the network.
- Both must be on the same network. Guest networks and some office networks stop devices seeing each other.
- Check that Therbie is allowed in Settings › Privacy & Security › Local Network on the device, and in System Settings › Privacy & Security › Local Network on the Mac.
- After updating Therbie on the device, open it again: updating closes it.
The Mac shows "Not paired" for a device that was paired
The pairing was removed on one side: on the device under Paired Macs, or on the Mac with Unpair. A restored or new device also needs to pair again. Click Pair… and tap Allow on the device. See Pair your Mac and devices.
The device never shows the pairing request
- Therbie isn't on screen. It has to be on screen on the device, with Allow my Mac to run tests on. A device in the background answers "Open Therbie on the device to pair."
- A request was just declined or ignored. After Don't Allow, or a request nobody answered, the device ignores new requests for 30 seconds.
- The request timed out. It waits about a minute. Click Pair… again.
The Mac says "Can't share right now"
This message appears on the Mac, under the Share this Mac's status switch. It means macOS refused to let Therbie announce itself on the network. Therbie retries every few seconds.
- Open System Settings › Privacy & Security › Local Network and make sure Therbie is allowed.
- Switch sharing off and on again.
- If it persists, restart the Mac.
If Local Network access is turned off, the Mac says so instead: "Therbie can't use the local network."
Mac Display says "Pair With Your Mac"
The Mac is sharing its status, but this iPhone or iPad isn't paired with it, or the pairing was removed on the Mac. Pair them: see Pair your Mac and devices. Mac Display connects by itself once they're paired.
Mac Display or the Your Mac card says "Not seen"
- Check that Share this Mac's status with my iPhone and iPad is on (the iPhone & iPad Display button on the Mac's This Mac page), and that the Mac is awake.
- Make sure the iPhone or iPad is on the same network as the Mac.
- If you tapped Stop Looking for Macs, open Mac Display again to start looking.
- Up to 4 devices can watch one Mac at a time.
A widget shows an old reading
iOS decides when widgets refresh, and refreshes them less often on low battery. The widget's Updated time shows how old the reading is; after 30 minutes it turns to Updated … ago. Leaving Therbie refreshes all widgets. See Widgets, Lock Screen and StandBy.
Alerts don't appear
- Therbie isn't running. Alerts only fire while Therbie is on screen, the floating monitor is open, or a trip or background logging keeps it running. See Why background alarms are rare.
- Notifications are off for Therbie. The Alerts sheet then shows Turn On in Settings.
- The level was already passed. An alert fires when a reading reaches its level. If the battery was already past the level when Therbie started watching, the alert waits for it to drop and rise again.
- The same alert fired recently. It doesn't repeat within 10 minutes.
- To check notifications work, tap Send Test Alert.
A test stopped by itself
On the iPhone or iPad, a benchmark or throttle test stops if:
- you leave Therbie. iOS doesn't allow tests in the background;
- the device reaches Critical.
A test started from the Mac keeps running if the Mac disconnects, and its result is sent when they reconnect. A device in Low Power Mode refuses tests from the Mac: "Low Power Mode is on. It caps performance, so results wouldn't be comparable." Check the run plan's log on the Mac for the reason.
My results are lower than last time
Start at Normal, in the same room and position, with the same charge state. These all lower results:
- heat left over from an earlier test;
- a warmer room;
- Low Power Mode;
- a debug build from Xcode.
See How long should a throttle test be?
A sensor won't turn on
- The tile says "Not on this device". The device doesn't have that sensor, for example a barometer or step counting on some iPads.
- The Sensors screen says "Not allowed. Change it in Settings › Therbie." You declined a permission (Location, Microphone, Camera, Motion & Fitness or Bluetooth). Turn it on in Settings › Therbie.
- Sensors only run while Therbie is on screen, unless a trip is recording or the sensor has Keep logging in the background on.
Siri doesn't respond
- Every Therbie phrase includes "in Therbie", for example "How hot is my phone in Therbie".
- If holding the side button doesn't open Siri, search Settings for "side button".
- You can also run the actions from Spotlight, the Shortcuts app or the Action Button. See Shortcuts and Siri.